Craftsman Industrial tools are American made. Whether you're a professional in need of new hand tools or someone who just needs a new set of quality hand tools. Craftsman 3/8' Drive Quick. Build a Craftsman Wall Cabinet. Photo: Michael Pekovich Hidden practicality. A tilting drawer offers handy, attractive storage. Set up the tablesaw to cut 1. Craftsman; Product type: Hand tools, power tools, lawn and garden equipment, work wear: Owner. Since 1991, Sears has run the Craftsman Club customer loyalty program, one of the oldest such programs by a retailer. How to Delete All Old Codes From My Sears Craftsman Garage Door Opener. Build a Craftsman Wall Cabinetmore on woodworking safety. Tools and Materials. Drill Press. Tablesaw. No surprise however since this is the usual case for any set of Craftsman tools. This is the perfect set when starting to build up my tool. Get Craftsman quality from Sears. Deals; Coupons; Local Ad; Gift Ideas. Gifts; Gift Cards; Gift. Handsaw. Block plane. Bandsaw. Router. Chisel. There is always a spot for a wall cabinet, especially a small one. This Craftsman- style piece is modeled after a clock, and at a little more than a foot wide it fits well in almost any tight, vertical space. I made it out of butternut, an underused, medium- toned wood that works easily. Because this cabinet was destined for a kitchen, I outfitted the inside to accommodate spices, but the same- sized cabinet could hold anything from pottery to small books. The shelves, in this case, are spaced to fit off- the- rack spice bottles, with the bottom shelf roomy enough for larger, bulk- sized decanters. The tilting drawer at the bottom is made to fit large packages of tea. On this small, vertical cabinet, I could have dovetailed the case, but I saw no need to spend the time when countersunk and plugged screws would do. And on such a simple piece, I didn’t want anything to detract attention from the door, where I spent most of the design and construction energy. I used a flat panel at the bottom of the door to cover the drawer and bulk items, but at the top I installed glass to show off the nicer- looking spice bottles and to make the piece a bit more interesting. Over the single piece of glass, I installed muntins, giving the appearance of two- over- two panes of glass. This project originally appeared in the January/February 2. Fine Woodworking (FWW #1. Photos by Matthew Teague and Michael Pekovich. ![]() Craftsman 315 Keypad Diagnosis & Repair Garage Door Opener. How To Program a Craftsman Garage Door Opener Keypad - Duration. How to build a Garage - Duration. Craftsman Eager 1 Lawn Mower Parts Manual Pdf. The Lego Mindstorms Ev3 Laboratory Build Program And Experiment With Five Wicked Cool Robots. ![]() Drawings by Vince Babak. How to Make. Build and glaze the door. Mill the lumber: The top and bottom are 1 in. Build the basic case: Don’t waste energy with complex methods of building the case. Set up the tablesaw to cut 1. Use a stop on your miter gauge to ensure that the dadoes in the back and sides will line up. It’s not really necessary to dado the back panel for the shelves, but doing so eases glue- up. The first step in the process is rabbeting the top and bottom—because the same stop location can be used for each—on all three pieces. Then locate each shelf and set the stop on your miter gauge. On the two sides, use the same setup to cut another 1. With the dadoes lined up on the back and sides of the case, trim all of the shelves to width and length and install the 3. Locate the position by marking off the width of the drawer front, then inset the stop another 3. A screw holds the stop in place and allows it to pivot. On the bottom shelf, cut a 1. This groove will work as a hinging mechanism for the tilting drawer. With the drawer stop installed and the groove cut, you can glue up the case, which should go smoothly on such a small piece. Install the top and bottom: Making the bottom of this case out of 1- in.- thick stock gives the piece a grounded look. Just remember to leave a 1. It lends the piece a nice, finished look and helps draw your attention to the glass panels in the door. Then establish the overhang, in this case 1- 1. If it feels safe, use the tablesaw. With the piece held upright, sight down the raised blade and adjust the angle until it enters at the bottom of the bead and exits at the overhang line. You can achieve the same results by cutting to the line with a handplane. The result is a rounded top edge that angles back sharply toward the case. Both the top and bottom are simply screwed onto the case and pegged. Build the drawer: When you open this case, the drawer at the bottom is a nice surprise. Instead of sliding as a normal drawer would, this tall drawer tilts forward and down so that you can reach in for tea or whatever you decide to store inside. The sides and back are rounded so that the drawer slides open easily with the pull—nothing more than a 3. By twisting the stop you can easily remove the whole drawer for easy cleaning or restocking. Make sure you cut the front 1. The side edges of the front and back are rabbeted to accept the sides. The two sides and the back are all shaped on the bandsaw, and a small notch is removed from the top center of the back to allow for the drawer stop. Rout this bead on the inside of the drawer front, then use a dado blade to remove the front edge. This bead should fit nicely into the groove on the bottom of the case and allow the drawer to fall forward. The drawer is glued up with the bottom floating in the dadoes, and a few brads in the sides and back hold everything in place. Miter the bridle joint: A simple miter jig clamped onto the rails and stiles helps guide the chisel for the 4. This simple detail lends a framed and finished look to the door. Assemble and glue up the door: Once you’ve milled and trimmed a center panel for the bottom of the door, the door can be glued up. However, be sure to dry- fit your joints first. It's best to work out any problems before you begin glue- up. A dry run ensures that everything fits and that the bridle joints pull tight. Install the muntins: The final touch to this door is to install the muntins. Then use a small gentleman’s saw to cut the 4. Once the two pieces press- fit into place, lay one across the other and mark the centers. When installed, a few drops of glue at the groove and on the mitered ends, along with a little tension from the door itself, hold everything in place. Install and add finishing touches to the door: Once the glass slides in, small pieces of molding are used to secure it. All that’s left to do is to hang the door and apply the finish and hardware. I used an oil varnish from Waterlox to give this piece a natural look and to provide protection. The hinges I used are antiqued, solid brass H- hinges from Horton Brass, and the knob is a Shaker- style bronze knob from Colonial Bronze. After you’re done, open the cabinet, reach in the drawer, and fix yourself a cup of tea. So for inspiration, for conversation, for exclusive deals .
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2016
Categories |